GrimmSpeed
2008-12-28, 11:01 PM
We are continually improving our products to maintain the high standards you(our customers) expect from a company like ours. This is a job we truly take to heart...and truly enjoy.
Recently we have made a few updates to our exhaust pipe line:
1. Exhaust Pipe Flanges now CNC Machined - We have sold over 600 exhaust pipes and for the most part, all flanges have been good. However, we did have one batch that had some flanges with a bit of warping. We took care of any customers that did have a problem(only a handful), however, we need to make sure something like this does not happen again. All pipes will have CNC Machined flanges us which ensures that the flanges will remain perfectly flat.
http://www.grimmspeed.com/images/product_images/ewg_uppipe_44mm_300_8.jpg
2. Flex Joint - Upgrade to thicker stainless - From the start we have always used a very high quality flex joint, in doing so we have had no issues with the flex joint. Recently we have come across a flex joint that has even thicker piping...of course we need to upgrade to this new flex joint. All pipes now contain this even stronger flex joint!
http://www.grimmspeed.com/images/product_images/up_pipe_300_6.jpg
3. Length of HiFlow Crosspipe - We have extended this pipe by a few millimeters. Out of 250 HiFlow Crosspipes sold this month we have had a couple that were slightly to short. This has been fixed and we will continue to expect our quality assurance crew to keep an eye on them for you.
4. EWG Side-Outlet Support - Our EWG Up pipes are now equipped with a support underneath the sideoutlet to ensure you will have no cracks in the top weld of the side outlet. We havent had issues with this, but we know some of our competitors have, so we are just being proactive to make sure we continue to be free of problems.
http://www.grimmspeed.com/images/product_images/ewg_uppipe_44mm_300_3.jpg
Thank you for your continued support. We will keep working hard over here to maintain our premium quality standards!
Justin
Recently we have made a few updates to our exhaust pipe line:
1. Exhaust Pipe Flanges now CNC Machined - We have sold over 600 exhaust pipes and for the most part, all flanges have been good. However, we did have one batch that had some flanges with a bit of warping. We took care of any customers that did have a problem(only a handful), however, we need to make sure something like this does not happen again. All pipes will have CNC Machined flanges us which ensures that the flanges will remain perfectly flat.
http://www.grimmspeed.com/images/product_images/ewg_uppipe_44mm_300_8.jpg
2. Flex Joint - Upgrade to thicker stainless - From the start we have always used a very high quality flex joint, in doing so we have had no issues with the flex joint. Recently we have come across a flex joint that has even thicker piping...of course we need to upgrade to this new flex joint. All pipes now contain this even stronger flex joint!
http://www.grimmspeed.com/images/product_images/up_pipe_300_6.jpg
3. Length of HiFlow Crosspipe - We have extended this pipe by a few millimeters. Out of 250 HiFlow Crosspipes sold this month we have had a couple that were slightly to short. This has been fixed and we will continue to expect our quality assurance crew to keep an eye on them for you.
4. EWG Side-Outlet Support - Our EWG Up pipes are now equipped with a support underneath the sideoutlet to ensure you will have no cracks in the top weld of the side outlet. We havent had issues with this, but we know some of our competitors have, so we are just being proactive to make sure we continue to be free of problems.
http://www.grimmspeed.com/images/product_images/ewg_uppipe_44mm_300_3.jpg
Thank you for your continued support. We will keep working hard over here to maintain our premium quality standards!
Justin