Rory's list of WTB
 

Bump from the dead. Need some things to finish off the build, in a hurry. So, currently looking for:


- '05+ STi steering wheel, or '06-07 WRX driver's airbag if it'll fit the '04 STi wheel (anyone know?).

- Peanut WRX front grill.

- '08+ STI grill and trunk badges.

- Cusco (rep ok) peanut front lip, PSM.

- WRX side skirts, PSM.

- Other stuff that I didn't know I needed to make my car better


I think that's about it for now. Will update as more is needed/acquired.


Thanks all!

parts
 

Rory, I have the fsb bushings that I forgot to give you when you picked up your stuff RC

I have a 27mm Whiteline rear sway.

Sweet! Let's figure something out to pick em up!

I'm pretty sure that'd be overkill for my 25mm hollow front :(

Might not be. Rotation is good for autocross and this would help compensate if you had excessive rear camber for wheel fitment or something (been there). Just a thought. If you drive the car during the Winter, maybe remove the RSB.

Well if you want, I have a 32mm hollow front too lol

Holy jeebus. Hadnt heard there was a 32mm lol

I'm tryig to keep it mellow as it's a daily still. Thinking 25 all around is tops for me.

More concerned about road manners, hence keepin it simple, and small. Not going big on wheels/tires, at least not for a while. And don't want crazy camber, again the whole mellow thing. Need to be able to drive it on the crap roads out here, and keep her happy

No worries, they have been laying in my garage for a while, so if you change your mind I'm sure they will still be here.

That's what I have, 25 front, 27 rear. :D

And wagons tend to oversteer more than sedans, everything else being equal.

One more reason to like 'em!

I have a 25mm hollow front, so roughly 22mm solid, 25mm rear would be a softer version of your setup., and what I'm going for. The Cobb/Hotchkis setup seems dialed, for a mellow pairing.

Also keep in mind that the only time you will really notice sways when driving on the street is when you are going down a driveway or slant that will cause the car to pick up one wheel.

So do I! :cool:

I have a set of 06-07 door cards. They are from a TR I think as they are grey and black. They are the door cards only. I also have an all black rear seat (with pass through) from a 2004 wrx. Not sure if these are what you are looking for, but they are what I have! Thanks
Ryan

The 06-07 door cards I'm looking for are the "Limited" black leather.

But whacha want for the back seats?

Gotcha, that's what I figured but thought I should ask anyway.

Seems like about $150 is the rear seat going rate on NASIOC, so how about $100? Let me know
Ryan

Ryan, might wantto take you up on that seat if you're still interested in gettin rid of it, have a set of all black fronts on the way.

Let me know if you still hav this/don't want it. And how much :)

'atta boy. ;)

I sure do! Retail is $263.94...so how about $180?

Sway and bushings only? How many miles on it?




Looks like I'm gonna need a set of rear stout mounts or similar and a set of rear endlinks :)

:)

You don't need endlinks or rear mounts. My car had the 27mm bar on it for quite a while and had no problems. The stock endlinks on the STi are pretty stout and the mounts are beefy too.

I'll have to rummage around for the bushings, I'm pretty sure I have them. I'll let you know.

**I do have the bushings for that bar.**

Good deal, let me know when and where you'd like to meet up!

You have a PM

You can definitely take the seat. Hit me up with a PM on when you want to meet up. End of this week would work well. Thanks
Ryan

I have 2007 Sti seats driver and passenger interested?

I have an STi, and not a fan of blue interiors. If you were talking Limited leather setup, I'd probably take everything but the front seats if the price was right, would go well with the leather/suede fronts coming in soon.

I'm back, and got to see/drive the car for the first time in a month, so back to needing stuff lol :(


Tried installing the Recaro seats using the Wedge Engineering brackets that came on my Momos, no go. Either need advice on modifying these, or some new brackets. So, anyone have a set of Speedware brackets? Maybe Sparco non-height-adjustables?

Don't be selfish. Post up a picture of this mines trunk!

only have one on my phone, it's on FB, but I can't seem to link it :(

http://a3.sphotos.ak.fbcdn.net/hphot..._4363555_n.jpg


this work?

Looks great!

Nice man! Where did you have it done?

Very nice. Like a small old school porsche turbo thing sort of.

I got the '06-'07 wrx decklid from Ray C, had the trim and keyhole shaved, had a Bayson R replica lip trimmed before epoxy and bolted in place, then glassed in. Guy that did the work is Ferdie at Ferdie's Classy Chassis, he just finished my dad's '66 vette resto (the two of them were at it for two years), been at chassis and body for 50+ years.

Main trimming performed was to get the front to sit a bit lower, kicking the lip up more for a bit more pronounced duckbill look. Also had him leave enough of the lower edge visible to replicate the factory decklid sculpting. Couldn't be happier with the way it turned out :)

Paint was done by a contact of KSpeed, they also did a new OE front bumper as mine was cut hell for previous FMIC set up.

Do you still have the old bumper?

I think I do. Not sure if Matts gonna let me take it. Would like to go fmic with a big turbo setup down the road :)

Gonna make an attempt at entering my pos in Top Scoob. Need goodies. First post edited.

I've got a set of GroundControl rear camber plates for the GD. Really nice shape, low miles. Been sitting in a bag for like 5 years now since I went to the Tein SuperRace coilovers on my race car.

Edit, found a picture:

http://www.seccs.org/gallery/Car%20P...nts%20Rear.jpg

:banana: how much?

I'll take those blue valve stems off your hands. I take it the caps are blue too? Lemme know how much. :)

Idk to be honest, they should be on the way today, so will know for sure in a week.. They'd be BNIpackage Enkei aluminum stems and caps. I just want chrome or black of the same. So, price is a set of raw/chrome/polished/etc. stems/caps.

Oh ya they do because the same ones came with my friends RPF's. Ok well just let me know how much that is hen you find out.

They sell new for $300... so half that? $150? BTW: these top mounts are sized for 2.5" springs and Koni diameter struts (same as stock)... I *think* the KWs are the right size because people run them with stock or Group-N top mounts, but don't quote me on that.

FYI: GC makes an awesome over-mount matching front pair too: http://www.ground-control-store.com/...p/II=150/CA=97

Gonna need to hit up Cory and check what "modifications" he had to perform to get the coils installed - I know he fought with the fronts, not sure on the rears - I'm on Group Ns now.

If he says go, you got a deal.


And thanks for the headsup on the fronts - I hadn't seen the top mount style before. Might not gain any drop with them, but won't lose any.

The overmounts usually allow the car to ride ~1 inch lower w/o losing suspension travel. Maybe not necessary depending on the coilovers you're running and how much adjustability they have, but they were definitely nice if you're running a Koni/GC setup that's not independent ride-height adjustable.

And if you're running Group-N top hats in the rear right now, the GC top mounts should be a direct replacement. :cool: